Sunscreen water resistance is demonstrated in vivo: the SPF of a product is measured before and after standardised immersion cycles, and the percentage of protection retained is then calculated. In Europe, ISO 16217 describes the immersion procedure and ISO 18861 the calculation of percentage water resistance. In the United States, the FDA requires its own protocol, with claims limited to 40 or 80 minutes.
Why does water resistance require a dedicated test?
A sunscreen can lose a significant share of its protection on contact with water. The film formed on the skin dilutes, breaks up or washes off, especially when the formula relies on poorly film-forming emollients or water-soluble filters. An SPF measured on dry skin therefore says nothing about the protection left after a swim.
A “water resistant” claim has a direct bearing on consumer safety, since people rely on it to decide when to reapply. That is why it must be supported by a dedicated test, carried out using a method recognised in the target market. It is also one of the sun care claims most closely scrutinised by authorities and consumer associations during market checks.
How is a water resistance test run under ISO 16217?
ISO 16217:2020 describes an immersion procedure carried out on volunteers, combined with SPF determination under ISO 24444. The principle is to compare protection before and after water exposure within the same panel.
Protocol steps
- Application: the product is applied at 2 mg/cm² to delimited sites on the back, as in a standard SPF test, then left to dry.
- Immersion: volunteers are immersed in a pool with controlled temperature and agitation, in 20-minute cycles separated by air-drying periods, without towelling.
- Number of cycles: two 20-minute cycles for a “water resistant” claim, four cycles for “very water resistant”.
- Irradiation and reading: the immersed sites are then irradiated and erythema is read as in an ISO 24444 test, giving the post-immersion SPF.
- Comparison: this post-immersion SPF is compared with the static SPF, measured without immersion on the same panel.
Water quality, temperature, pool agitation and drying times are all specified by the standard, because each of these parameters strongly affects the result.
The panel meets the same criteria as an ISO 24444 SPF test: fair skin and at least ten valid results. Because individual results are more scattered after immersion than under static conditions, laboratories often recruit more volunteers to meet the final statistical criterion.
How is percentage water resistance calculated?
ISO 18861:2020 defines how percentage water resistance (% WRR) is calculated. It compares the protection retained after immersion with the initial protection, subtracting 1 from both SPF values so that only the protection actually provided by the product is considered:
% WRR = (post-immersion SPF − 1) / (static SPF − 1) × 100
In Europe, a product may claim water resistance if at least 50% of its protection is retained. The criterion applies to the lower limit of the confidence interval calculated across the panel, not just to the mean: an average result slightly above 50% is therefore not always enough.
How do European and US requirements differ?
The two major markets follow different claim logics. In Europe, the test shows that a sufficient share of the SPF is retained. In the United States, the SPF measured after immersion is the value that appears on the label.
Comparison of water resistance requirements
| Criterion | European Union | United States (FDA) |
|---|---|---|
| Reference | Recommendation 2006/647/EC, ISO 16217 and ISO 18861 | OTC sunscreen regulations |
| Tested duration | 2 × 20 min (water resistant) or 4 × 20 min (very water resistant) | 40 or 80 minutes of immersion |
| Pass criterion | At least 50% of protection retained | Labelled SPF is the post-immersion SPF |
| Permitted wording | “Water resistant”, “very water resistant” | “Water resistant (40 minutes)” or “(80 minutes)” |
| Prohibited wording | Any claim of total protection | “Waterproof”, “sweatproof” |
| Volunteers | Yes, in vivo test | Yes, in vivo test |
Australia applies AS/NZS 4399:2020, which allows longer water resistance durations to be claimed, up to four hours. A product intended for several markets therefore often has to go through several protocols, and it is worth planning them together on a single batch.
Laboratories equipped for immersion testing remain fewer than those running static SPF tests. To find providers offering water resistance testing under European, US or Australian protocols, you can search for a laboratory on Skinobs.
Are there in vitro methods for assessing water resistance?
There is currently no standardised in vitro method that can support a water resistance claim. ISO 23675, published in late 2024 for in vitro SPF, explicitly excludes this measurement from its scope.
In vitro approaches do exist for formulation screening, however. They involve, for example, immersing product-coated PMMA plates in agitated water and comparing absorbance spectra before and after immersion. These methods are fast and inexpensive, and help rank several prototypes against each other. Their correlation with in vivo results remains too weak to support a claim.
Formulation choices also weigh heavily on the outcome, well before any test. Film-forming polymers, water-repellent emollients and the balance between oil-soluble and water-soluble filters all influence how well the film survives immersion. Comparing several prototypes in vitro on these parameters helps select the formula worth sending to an in vivo panel.
How should you prepare for a water resistance test?
A water resistance test costs more and takes longer than a static SPF test. A few precautions reduce the risk of failure and retesting.
- Screen early: an in vitro plate test helps rule out the weakest prototypes before a panel is recruited.
- Build in a margin: aim for a static SPF high enough for the post-immersion SPF to stay at the target level, especially for the US market.
- Choose the claim: decide from the start between “water resistant” and “very water resistant”, as the number of cycles changes the protocol and the budget.
- Specify the markets: tell the laboratory every region where the product will be sold, so it can propose a protocol covering each one.
Water resistance does not cover everything. How a product holds up against sweat, sand or towel rubbing calls for other evaluations, which will be covered in a dedicated article in this series.
FAQ
What is the difference between “water resistant” and “very water resistant”?
In Europe, “water resistant” corresponds to two 20-minute immersion cycles and “very water resistant” to four. In both cases, at least 50% of the protection must be retained.
Can a sunscreen be claimed as “waterproof”?
No. No major regulation allows it, because no product keeps all its protection in water. The FDA explicitly prohibits the terms “waterproof” and “sweatproof”.
Is an in vitro test enough to claim water resistance?
No. No in vitro method is currently validated for this claim. In vitro tests are only used to screen formulations during development.
Does water resistance guarantee protection after swimming?
It guarantees that a measured share of protection remains under standardised conditions. Reapplication is still recommended after swimming, physical exercise or towelling.
Find a laboratory for your water resistance testing
Skinobs brings together more than 9,000 users in 124 countries and lists cosmetic testing laboratories and solutions worldwide, including sun protection specialists. Explore the Skinobs platform to compare the protocols on offer and contact the providers that fit your markets.
The editorial team